ANALYSIS OF INJECTION MOLDING PROCESS TO REDUCED DEFECTS (SHORT-SHOT)
This paper deals with optimal injection molding process parameters for minimum short shot. In this study, analyses of injection molding process parameters were carried out to reduced defects and minimize short shots. Optimal injection molding conditions for minimum short shot were determined by the DOE technique of Taguchi and the analysis of variance (ANOVA) methods. For this study CPVC plastic specimen was tested. Determination of the optimal Injection molding process parameters were based on S/N ratios. According to results mold closing speed had significant effect on quality characteristic. Mold pressure and Injection pressure had no significant effect
Chen, R.S., Lee, H.H., and Yu, C.Y., “Application of Taguchi’s Method on the optimal process design of an injection molded PC/PBT automobile bumper”. Composite Structures, 39, 1997, pp. 209-214. DOI: https://doi.org/10.1016/S0263-8223(97)00110-4
Wang, W.H., and Tarng, Y.S., “Design Optimization of cutting parameters for turning operations based on the Taguchi method”. Journal of Materials Processing Technology, 84, 1998, pp. 122- 129. DOI: https://doi.org/10.1016/S0924-0136(98)00079-X
Phadke, M.S., “Quality Engineering Using Robust Design”. Prentice Hall International Inc., NewYork, 1989. DOI: https://doi.org/10.1007/978-1-4684-1472-1_3
Roy, R.K., “A primer on the Taguchi method”. Competitive Manufacturing Series, Van Nostrand Reinhold, New York 1990.
Shaik Mohamed Mohamed Yusoff, Jafri Mohd. Rohani, Wan Harun Wan Hamid & Edly Ramly “A Plastic Injection Molding Process Characterisation Using Experimental Design Technique: A Case Study”, Jurnal Teknologi, 41, 2004. DOI: https://doi.org/10.11113/jt.v41.686
Taguchi G, Konishi S. Taguchi methods, orthogonal arrays and linear graphs, tools for quality American supplier institute. American Supplier Institute; 1987.
Taguchi G, Introduction to quality engineering, (Asian Productivity Organization, Tokyo, 1990).
Roy, R. A Primer on the Taguchi Method. New York: Van Nostrand Reinhold; 1990.
Copyright (c) 2018 L.D.Mahajan, P.N.Ulhe
This work is licensed under a Creative Commons Attribution 4.0 International License.
License and Copyright Agreement
In submitting the manuscript to the journal, the authors certify that:
- They are authorized by their co-authors to enter into these arrangements.
- The work described has not been formally published before, except in the form of an abstract or as part of a published lecture, review, thesis, or overlay journal.
- That it is not under consideration for publication elsewhere.
- That its release has been approved by all the author(s) and by the responsible authorities – tacitly or explicitly – of the institutes where the work has been carried out.
- They secure the right to reproduce any material that has already been published or copyrighted elsewhere.
- They agree to the following license and copyright agreement.
Authors who publish with International Journal of Engineering Technologies and Management Research agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License (CC BY-SA 4.0) that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors can enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or edit it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) before and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
For More info, please visit CopyRight Section