REPAIR, MAINTENANCE AND PROCEDURES TO PREVENT DEFECTS AND FAULT DETECTION TESTS - A LITERATURE REVIEW STUDY

  • Sanaz Jahangiri Australian Maritime College, University of Tasmania, Australia
Keywords: Pipe Defects, Inspections, Identifications, Technical Surveys

Abstract

A reliable technical method is required to analyze the present defects in the pipe. Technical inspections aiming at detecting technical points concerning the defects begins from scientific explanations from the damaged parts. Then, an analysis is made in view of materials and their engineering so that it is detected how these damages have occurred [1]. Production of reasonable technical results requires several items including expertise, experience and identification of required equipment and above all, well-disciplined material experts and engineers [2]. The procedure for technical survey of defects is performed as per following stages. • Collection of initial data • Determination of mechanism of the defects • Determination of sequence of defects • Testing the assumptions • Determination of reasons for facture and its cause • Reporting the results.

Downloads

Download data is not yet available.

References

Khlefa A. Esaklul a, Tawfik M. Ahmed. Prevention of failures of high strength fasteners in use in offshore and subsea applications, Engineering Failure Analysis, 2009. DOI: https://doi.org/10.1016/j.engfailanal.2008.07.012

J.B. Wintle, R.J. Pargeter. Technical failure investigation of welded structures (or how to get the most out of failures), Engineering Failure Analysis, 2005. DOI: https://doi.org/10.1016/j.engfailanal.2005.01.005

Hayes B. Six case histories of pressure vessel failures. Eng Fail Anal 1997.

Hayes B. Case histories of pressure vessel failures. Eng Fail Anal 1996; 3:115–27. DOI: https://doi.org/10.1016/1350-6307(96)00002-7

Challenger NV, Phaal R, Garwood SG. Int J Pressure Vessel Piping 1995; 61:433–56. DOI: https://doi.org/10.1016/0308-0161(94)00120-8

Matthews C. A practical guide to engineering failure investigation, ISBN 1 86058 086 6, First published by Professional Engineering Publishing; 1998. DOI: https://doi.org/10.1002/9781118902691

Wintle JB. Pressure systems casebook, First published by Professional Engineering Publishing; 2004 – ISBN to be supplied.

McHenry HI et al. Failure analysis of an amine absorber pressure vessel. Mater Performance 1987;26(8):18–24.

ManeeshSingh, Tore Markeset. A methodology for risk-based inspection planning of oil and gas pipes based on fuzzy logic framework, Engineering Failure Analysis, 2009. DOI: https://doi.org/10.1016/j.engfailanal.2009.02.003

L. Niu, Y.F. Cheng. Development of innovative coating technology for pipeline operation crossing the permafrost terrain, Construction and Building Materials 2007. DOI: https://doi.org/10.1016/j.conbuildmat.2007.06.001

Sanja Martinez, LidijaValek Z ulj, Frankica Kapor, Disbonding of underwater-cured epoxy coating caused by cathodic protection current, Corrosion Science, 2009. DOI: https://doi.org/10.1016/j.corsci.2009.06.003

Khlefa A. Esaklul, Tawfik M. Ahmed, Prevention of failures of high strength fasteners in use in offshore and subsea applications. Engineering Failure Analysis, 2008. DOI: https://doi.org/10.1016/j.engfailanal.2008.07.012

Aylor DM, Bowles CA, Tregoning RL, Gaudett MA. High strength fasteners for seawater immersion service. Proceeding of offshore pipeline workshop, Galveston, Texas; 1989.

Ross RW, Tuthill AH. Practical guide to using marine fasteners, 1900.

Cosham A, Hopkins P. The effect of dents in pipelines – guidance in the pipeline defect assessment manual. Int J Pres Ves Pip 2004;81: 127–39. DOI: https://doi.org/10.1016/j.ijpvp.2003.11.004

Macdonald KA, Cosham A. Best practice for the assessment of defects in pipelines – gouges and dents. Eng Fail Anal 2005;12(5): 720–45. DOI: https://doi.org/10.1016/j.engfailanal.2004.12.011

Cosham A, Hopkins P. An overview of the pipeline defect assessment manual. In: Denys R, editor. Proceedings of the fourth international pipeline technology conference, vol. 3. Oostende, Belgium: Scientific Surveys Ltd; 2004. p. 1487–502.

K.A. Macdonald, A. Cosham, C.R. Alexander, P. Hopkins؛ Assessing mechanical damage in offshore pipelines –Two case studies, 2006. Engineering Failure Analysis, 2007. DOI: https://doi.org/10.1016/j.engfailanal.2006.11.074

A.A. Carvalho, J.M.A. Rebello, M.P.V. Souza, L.V.S. Sagrilo, S.D. Soares. Reliability of nondestructive test techniques in the inspection of pipelines used in the oil industry. International Journal of Pressure Vessels and Piping, 2008. DOI: https://doi.org/10.1016/j.ijpvp.2008.05.001

ASME B31G. Manual for determining the remaining strength of A supplement to ANSI/ASME B31G Code for Pressure Piping, 1991.

Kiefner JF. Failure stress levels of flaws in pressurized cylinders. ASTM STP 536, American Society for Testing and Materials; 1973. p. 461–81. DOI: https://doi.org/10.1520/STP49657S

Kiefner JF, Vieth PH. Evaluating pipe 1: new method corrects criterion for evaluating corroded pipe. Oil Gas J 1990;88(32): 56–9.

DnV. Corroded pipelines recommended practice. Det Norske Veritas, RP-F101; 1999.

Cronin DS, Pick RJ. Experimental database for corroded pipe: evaluation of RSTRENG and B31G. In: Proceedings of the international pipeline conference, Calgary, Alberta, Canada, 2000.

Loureiro JF, Netto TA, Estefen SF. On the effect of corrosion defects in the burst pressure of pipelines. In: Proceedings of the 20th international conference on offshore mechanics and Arctic engineering, Rio de Janeiro, Brazil, 2001.

Benjamin AC, Freire JLF, Vieira RD, Castro JTP. Burst tests on pipelines with nonuniform depth corrosion defects. In: Proceedings of the 21st international conference on offshore mechanics and Arctic engineering, Oslo, Norway, 2002. DOI: https://doi.org/10.1115/OMAE2002-28065

Cronin DS, Pick RJ. Prediction of the failure pressure for complex corrosion defects. Int J Press Vessels Piping 2002;79: 279–87. DOI: https://doi.org/10.1016/S0308-0161(02)00020-0

Choi JB, Goo BK, Kim JC, Kim YJ, Kim WS. Development of limit load solutions for corroded gas pipelines. Int J Press Vessels Piping 2003; 80:121–8. DOI: https://doi.org/10.1016/S0308-0161(03)00005-X

Netto TA, Ferraz US, Estefen SF. The effect of corrosion defects on the burst pressure of pipelines. J Constr Steel Res 2005;61: 1185–204. DOI: https://doi.org/10.1016/j.jcsr.2005.02.010

،ایران تکنولوژی تحلیلگران های کانون شبکه http://nano.itan.ir/?ID=170 1388،(It was found in Msc Thesis which Dr.Khedmati was a supervisor).

Bouwkamp, J. G., Calif, U., Buckling and Post-Buckling Strength of Circular Tubular Sections, Offshore Technology Conference, 1975 (It was found in Msc Thesis which Dr. Khedmati was a supervisor). DOI: https://doi.org/10.4043/2204-MS

Published
2019-03-31
How to Cite
Jahangiri, S. (2019). REPAIR, MAINTENANCE AND PROCEDURES TO PREVENT DEFECTS AND FAULT DETECTION TESTS - A LITERATURE REVIEW STUDY . International Journal of Engineering Technologies and Management Research, 6(3), 15-20. https://doi.org/10.29121/ijetmr.v6.i3.2019.361