DESIGN AND CONSTRUCTION OF WITH WIND DRIVEN TURBO VENTILATOR
DOI:
https://doi.org/10.29121/ijetmr.v12.i12.2025.1711Keywords:
Greenhouse Drying, Vegetable Dehydration, Wind-Driven Ventilation, Turbo Ventilator, Passive Solar Drying, Energy-Efficient Drying, Sustainable Agriculture, Post-Harvest TechnologyAbstract
This study evaluates the performance of a greenhouse vegetable dryer integrated with a wind-driven turbo ventilator, developed to enhance natural convection and improve the drying process through renewable energy utilization. The design targets small-scale farmers in remote or off-grid are-as, where access to electricity and mechanical drying systems is limited or non-existent. The experi-mental setup involved drying freshly harvested leafy vegetables, which had an initial moisture content of approximately 80%. The test was conducted over a continuous 10-hour period under clear sunlight and moderate natural wind conditions. Key performance parameters—including internal and ambient temperatures, relative humidity, and vegetable moisture content—were systematically measured at two-hour intervals. The results revealed a consistent increase in internal temperature within the dryer, peaking at 49°C, which significantly exceeded the maximum ambient temperature of 33°C. This thermal gain was attributed to the greenhouse effect and the enhanced air circulation enabled by the wind-powered ventilator. Relative humidity within the drying chamber ranged from 55% to 62%, establishing an optimal environment for moisture evaporation. At the end of the drying cycle, the final moisture con-tent of the vegetables was reduced to 15%, marking a 65% total reduction. Compared to conventional passive solar dryers documented in the literature, this system demonstrated improved drying efficiency while maintaining simplicity and requiring no external power. Its performance aligns well with semi-passive systems and even rivals some electrically assisted dryers in efficiency. The ventilator played a key role by preventing internal heat saturation and promoting consistent airflow. Overall, the system offers a promising, cost-effective, and sustainable approach for post-harvest preservation of perishable crops in resource-limited settings.
Downloads
References
Akpinar, E. K. (2010). Drying of Mint Leaves in a Solar Dryer and Under Open Sun: Modelling, Performance Analyses. Energy Conversion and Management, 51(12), 2407–2418. https://doi.org/10.1016/j.enconman.2010.05.005
Al-Sanea, A. S., Zedan, M. F., and Al-Hussain, S. N. (2012). Effect of Thermal Mass on Performance of Insulated Building Walls and the Concept of Energy Savings Potential. Applied Energy, 89(1), 430–442. https://doi.org/10.1016/j.apenergy.2011.08.009
Arslan, D., and Özcan, M. M. (2008). Evaluation of drying Methods with Respect to Drying Kinetics, Mineral Content and Colour Characteristics of Rosemary Leaves. Energy Conversion and Management, 49(5), 1258–1264. https://doi.org/10.1016/j.enconman.2007.08.005
Bal, L. M., Satya, S., Naik, S. N., and Kar, S. K. (2011). Solar Dryer with Turbo Ventilator and Thermal Energy Storage for Drying Turmeric (Curcuma Longa L.): An Experimental Study. Journal of Food Process Engineering, 34(5), 1581–1600. https://doi.org/10.1111/j.1745-4530.2009.00540.x
Bala, B. K. (1996). Solar Drying Systems: Simulations and optimization. Solar Energy, 57(3), 243–250. https://doi.org/10.1016/S0038-092X(96)00100-7
Bala, B. K., Mondol, M. R. A., Biswas, B. K., Das Choudhury, B. L., and Janjai, A. S. (2003). Solar Drying of Pineapple Using Solar Tunnel Drier. Renewable Energy, 28(2), 183–190. https://doi.org/10.1016/S0960-1481(02)00036-3
Barnwal, P., and Tiwari, G. N. (2008). Grape Drying by Using Hybrid Photovoltaic-Thermal (PV/T) Greenhouse Dryer: An Experimental Study. Solar Energy, 82(12), 1131–1144. https://doi.org/10.1016/j.solener.2008.05.012
Bastide, D., Lauret, B., Boyer, M., and Garde, F. (2008). Building Ventilation: A Pressure Airflow Model Computer Generation and Elements of Validation. Energy and Buildings, 40(4), 648–660. https://doi.org/10.1016/j.enbuild.2007.05.011
Caputo, A. C., Pelagagge, P. M., and Salini, P. (2016). Economic Analysis of Solar-Powered Drying Systems for Food Processing. Drying Technology, 34(9), 1022–1037. https://doi.org/10.1080/07373937.2015.1087400
Chou, S. K., and Chua, J. C. (2001). New Hybrid Drying Technologies for Heat Sensitive Foodstuffs. Trends in Food Science and Technology, 12(10), 359–369. https://doi.org/10.1016/S0924-2244(01)00102-9
Datta, A. K. (2002). Heat and Mass Transfer in Food Processing. CRC Press. https://doi.org/10.1201/9781420041348
Doymaz, S. (2021). Drying of Thyme (Thymus vulgaris L.) and Selection of a Suitable Thin-Layer Drying Model. Journal of Food Processing and Preservation, 45(5), e15413. https://doi.org/10.1111/jfpp.15413
Edwards, H. G. M., Farwell, D. W., and Webster, D. (1997). FT Raman Microscopy of Untreated Natural Plant Fibres. Spectrochimica Acta Part A: Molecular and Biomolecular Spectroscopy, 53(13), 2383–2392. https://doi.org/10.1016/S1386-1425(97)00178-9
El-Sebaii, A. A., and Shalaby, S. M. (2012). Solar Drying of Agricultural Products: A Review. Renewable and Sustainable Energy Reviews, 16(1), 37–43. https://doi.org/10.1016/j.rser.2011.07.134
Fadhel, A., Abderrahim, K., and Kooli, A. (2011). Experimental Study of the Drying of Hot Red Pepper in the Open Air, Under Greenhouse and in a Solar Drier. International Journal of Renewable Energy Technology, 2(1), 1–16. https://doi.org/10.1504/IJRET.2011.037982
Food and Agriculture Organization of the United Nations. (2019). The State of Food and Agriculture 2019: Moving Forward on Food Loss and Waste Reduction. FAO.
Fudholi, A., Sopian, K., Othman, M. Y., Ruslan, M. H., and Bakhtyar, M. A. (2013). Energy Analysis and Improvement Potential of Finned Double-Pass Solar Collector. Energy Conversion and Management, 75, 234–240. https://doi.org/10.1016/j.enconman.2013.06.027
Fudholi, A., Sopian, K., Ruslan, M. H., Alghoul, M. A., and Sulaiman, M. Y. (2010). Review of solar Dryers for Agricultural and Marine Products. Renewable and Sustainable Energy Reviews, 14(1), 1–30. https://doi.org/10.1016/j.rser.2009.07.032
Fudholi, A., Sopian, K., Yazdi, M. H., Ruslan, M. H., Gabbasa, M., and Ibrahim, A. (2014). Performance Analysis of Solar Drying System for Red Chili. Solar Energy, 99, 47–54. https://doi.org/10.1016/j.solener.2013.10.019
Goyal, R. K., and Singh, P. P. (2022). Performance Evaluation of Greenhouse Dryer with Opaque North Wall. Energy Reports, 8, 119–125. https://doi.org/10.1016/j.egyr.2022.05.168
Henderson, S. M., and Pabis, S. (1961). Grain Drying Theory I: Temperature Effect on Drying Coefficient. Journal of Agricultural Engineering Research, 6(3), 169–174.
Hossain, M. A., and Bala, B. K. (2007). Drying of Hot Chilli Using Solar Tunnel Drier. Solar Energy, 81(1), 85–92. https://doi.org/10.1016/j.solener.2006.06.008
Hossain, M. A., Amer, K. A., and Bala, B. K. (2007). Drying of Hot Chilli Using Solar Tunnel Drier. Solar Energy, 81(1), 85–92. https://doi.org/10.1016/j.solener.2006.06.008
Hossain, M., and Bala, B. (2003). Drying of Tomato Using Solar Tunnel Drier. Renewable Energy, 28(2), 183–190. https://doi.org/10.1016/S0960-1481(02)00011-6
Janjai, H. (2010). A Greenhouse type Solar Dryer for Small-Scale Dried Food industries: Development and Dissemination. International Journal of Energy and Environment, 1(5), 861–870.
Janjai, S. (2012). A Greenhouse Type Solar Dryer for Small-Scale Dried Food Industries: Development and Dissemination. International Journal of Energy and Environment Engineering, 3, 1–7. https://doi.org/10.1186/2251-6832-3-25
Janjai, S., Intawee, P., Kaewkiew, J., Sritus, C., and Khamvongsa, V. (2011). A Large-Scale Solar Greenhouse Dryer Using Polycarbonate Cover: Modeling and Testing in a Tropical Environment of Lao People's Democratic Republic. Renewable Energy, 36(3), 1053–1062. https://doi.org/10.1016/j.renene.2010.09.008
Janjai, S., et al. (2009). Experimental and Simulated Performance of a Pv-Ventilated Solar Greenhouse Dryer for Drying of Peeled Longan and Banana. Solar Energy, 83(9), 1550–1565. https://doi.org/10.1016/j.solener.2009.05.003
Kabeel, A. E., Abdelgaied, M., and Essa, F. A. (2020). Enhancement of Hybrid Solar Desalination System Composed of Solar Panel and Solar Still by using Porous Material and Saline Water Preheating. Solar Energy, 204, 382–394. https://doi.org/10.1016/j.solener.2020.04.090
Karim, M. A., and Hawlader, M. N. A. (2006). Performance Investigation of Flat Plate, V-Corrugated and Finned Air Collectors. Energy, 31(4), 452–470. https://doi.org/10.1016/j.energy.2005.02.013
Khalloufi, M. A. M., Ratti, C., and Gariepy, Y. (2019). Quality Attributes of Fruits and Vegetables Dried by Emerging Drying Technologies. Critical Reviews in Food Science and Nutrition, 59(16), 2577–2594. https://doi.org/10.1080/10408398.2018.1456402
Kim, M. K., Kim, H. J., Choi, H. S., and Jeong, J. W. (2014). Field Measurements and Numerical Analysis on the Performance of a Turbo Ventilator. Building and Environment, 76, 58–68. https://doi.org/10.1016/j.buildenv.2014.03.007
Kiranoudis, C. T., Maroulis, Z. B., and Marinos-Kouris, D. (1992). Drying Kinetics of Some Fruits. Drying Technology, 10(5), 1093–1113. https://doi.org/10.1080/07373939208916511
Kumar, A., and Tiwari, G. N. (2008). Effect of Wind Speed on Performance of a Greenhouse Dryer. Agricultural Engineering International: CIGR Journal, 10, Manuscript 08 009.
Kumar, A., Chauhan, P. S., and Dhiman, R. C. (2018). Thermal Performance of a Solar Greenhouse Dryer Using Different Methods of Heat Storage. Journal of Food Process Engineering, 41(2), e12563. https://doi.org/10.1111/jfpe.12563
Malik, M. A. S., Tiwari, G. N., Kumar, A., and Sodha, M. S. (1982). Solar Distillation. Pergamon Press. https://doi.org/10.1016/B978-0-08-025478-0.50007-3
Mathur, J., Mathur, G. D., and Anup, S. (2006). Performance of Non-Conventional Energy Assisted Turbo Ventilator. Renewable Energy, 31(12), 1975–1984. https://doi.org/10.1016/j.renene.2005.09.016
Mathur, J., Mathur, G. D., and Sodha, M. S. (2006). Experimental Performance of a Directional Turbine Ventilator. Renewable Energy, 31(14), 2297–2308. https://doi.org/10.1016/j.renene.2005.11.005
Miranda, J. M., Anton, X., Redondo-Valbuena, C., Roca-Saavedra, P., Rodriguez, J. A., and Cepeda, A. (2015). Egg and Egg-Derived Foods: Effects on Human Health and use as Functional Foods. Nutrients, 7(1), 706–729. https://doi.org/10.3390/nu7010706
Misha, S., Mat, S., Ruslan, M. H., Sopian, K., and Mahlia, T. M. I. (2016). Performance of a Solar-Assisted Solid Desiccant Dryer for Kenaf Core Drying. Drying Technology, 34(10), 1231–1241. https://doi.org/10.1080/07373937.2015.1099544
Misha, S., Mat, S., Ruslan, M. H., Sopian, K., and Salleh, E. (2015). Performance of a Solar-Assisted Solid Desiccant Dryer for Oil Palm Fronds Drying. Solar Energy, 112, 194–204. https://doi.org/10.1016/j.solener.2014.11.017
Mujumdar, A. S. (2014). Handbook of Industrial Drying (4th ed.). CRC Press. https://doi.org/10.1201/b17089
Nwakuba, S. N., Nwaigwe, K. N., and Okoye, P. A. C. (2020). Energy Consumption and Economic Costs of Different Dryers for Cassava Processing. Energy Reports, 6, 486–499. https://doi.org/10.1016/j.egyr.2019.09.013
Oosthuizen, T. P. (2016). Solar Drying of Fruit: A Comparison of Different Dryer Types. Acta Horticulturae, 1139, 559–566. https://doi.org/10.17660/ActaHortic.2016.1139.96
Page, M. J. (1949). Factors Influencing the Maximum Rates of Air Drying Shelled Corn in Thin-Layers (Master’s thesis). Purdue University.
Patil, A. K., Kapatkar, J. S., and Prabhu, S. V. (2012). Experimental Investigations on a Turbo Ventilator. Journal of Energy in Southern Africa, 23(4), 10–17.
Patil, A. K., Kapatkar, J. S., and Prabhu, S. V. (2013). CFD Analysis of a Turbo Ventilator. International Journal of Ventilation, 12(3), 271–282. https://doi.org/10.1080/14733315.2013.11684019
Prakash, O., and Kumar, A. (2014). Solar Greenhouse Drying: A Review. Renewable and Sustainable Energy Reviews, 29, 905–910. https://doi.org/10.1016/j.rser.2013.08.084
Prakash, S., Kumar, V., and Kumar, A. (2021). Performance Evaluation of Greenhouse Dryer with Latent Heat Storage. International Journal of Energy Research, 45(2), 2008–2023. https://doi.org/10.1002/er.5902
Ramaswamy, H. S., and Marcotte, M. (2005). Food Processing: Principles and Applications. CRC Press. https://doi.org/10.1201/9781420028873
Riffat, S. J., and Gillott, P. (2006). Passive and Low Energy Cooling of Buildings. Renewable Energy, 31(4), 445–470. https://doi.org/10.1016/j.renene.2005.04.010
Salem, M. R., Ali, R. K., and Elshazly, M. M. (2021). Experimental Investigation of the Performance of a Large-Scale Greenhouse Type Solar Dryer for Drying Dates. Energy Reports, 7, 174–181. https://doi.org/10.1016/j.egyr.2021.06.028
Sharma, S. K., Sethi, V. P., and Chauhan, M. S. (2021). A Review on Application of Turbo Ventilator in Buildings and Solar Dryers. Materials Today: Proceedings, 46(17), 7825–7830. https://doi.org/10.1016/j.matpr.2021.02.496
Sharma, S. K., Sethi, V. P., Chauhan, M. S., and Thakur, P. S. (2022). Design and Performance Evaluation of a Hybrid Photovoltaic-Thermal (PVT) Greenhouse Dryer for Medicinal Plants. Journal of Thermal Analysis and Calorimetry, 147, 1095–1111. https://doi.org/10.1007/s10973-020-10400-y
Shukla, S. K., Sethi, V. P., Sharma, S. K., and Chauhan, M. S. (2022). Performance Analysis of Greenhouse Dryer with Phase Change Material as Thermal Energy Storage. Journal of Thermal Analysis and Calorimetry, 147, 1221–1232. https://doi.org/10.1007/s10973-020-10400-y
Singh, P. P., Gaur, S. K., and Singh, D. S. (2021). Design and Development of Greenhouse Dryer Integrated With Turbo Ventilator. Materials Today: Proceedings, 46(17), 7791–7795. https://doi.org/10.1016/j.matpr.2021.02.489
Singh, P. P., Gaur, S. K., and Singh, D. S. (2021). Performance analysis of Greenhouse Dryer Using Different Absorbing Materials. International Journal of Ambient Energy, 42(10), 1171–1178. https://doi.org/10.1080/01430750.2019.1594368
Singh, P. P., Gaur, S. K., and Singh, D. S. (2022). Experimental Investigation of Drying Kinetics of Mint Leaves in a Solar Dryer Integrated with Turbo Ventilator. Journal of Food Process Engineering, 45(3), e13965. https://doi.org/10.1111/jfpe.13965
Singh, P. P., Gaur, S. K., and Singh, D. S. (2022). Performance Evaluation of Forced Convection Mixed-Mode Solar Dryer for Drying of Stevia Leaves. Energy Sources, Part A: Recovery, Utilization, and Environmental Effects, 44(1), 1848–1865. https://doi.org/10.1080/15567036.2022.2056026
Sodha, M. S., Bansal, N. K., Kumar, A., Bansal, P. K., and Malik, M. A. S. (1987). Solar Crop Drying (Vols. I and II). CRC Press.
Sopian, K., Daud, W. R. W., Othman, M. Y., and Yatim, B. (1998). Thermal Performance of the Double-Pass Solar Collector with and without Porous Media. Renewable Energy, 14(1–4), 369–374. https://doi.org/10.1016/S0960-1481(98)00091-1
Sreekumar, A., Manikantan, P. E., and Vijayakumar, K. P. (2008). Performance of Indirect Solar Cabinet Dryer. Energy Conversion and Management, 49(6), 1388–1395. https://doi.org/10.1016/j.enconman.2008.01.005
Tiwari, G. N. (2002). Solar Energy: Fundamentals, Design, Modelling and Applications. Narosa Publishing House.
Yaldiz, K. A., and Ertekin, C. (2001). Thin Layer Solar Drying of Some Vegetables. Drying Technology, 19(3–4), 583–597. https://doi.org/10.1081/DRT-100103936
Zedan, M. F., and Al-Sanea, A. S. (2010). CFD Simulations for Flow and Heat Transfer in a Ventilated Cavity with a Rotating Ventilator. Numerical Heat Transfer, Part A: Applications, 58(7), 543–564. https://doi.org/10.1080/10407782.2010.509669
Published
How to Cite
Issue
Section
License
Copyright (c) 2025 Abubakar R.A.
This work is licensed under a Creative Commons Attribution 4.0 International License.
License and Copyright Agreement
In submitting the manuscript to the journal, the authors certify that:
- They are authorized by their co-authors to enter into these arrangements.
- The work described has not been formally published before, except in the form of an abstract or as part of a published lecture, review, thesis, or overlay journal.
- That it is not under consideration for publication elsewhere.
- That its release has been approved by all the author(s) and by the responsible authorities – tacitly or explicitly – of the institutes where the work has been carried out.
- They secure the right to reproduce any material that has already been published or copyrighted elsewhere.
- They agree to the following license and copyright agreement.
Copyright
Authors who publish with International Journal of Engineering Technologies and Management Research agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License (CC BY-SA 4.0) that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors can enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or edit it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) before and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
For More info, please visit CopyRight Section
