COMPARISON STUDY BEWTWEEN THE RECOVERY BEHAVIOR OF DEFORMED QUENCHED, PRE-ANNEALED AND PULSED LASER DAMAGED Fe50Ni50 ALLOY BY MAGNETIC MEASUREMENTS
DOI:
https://doi.org/10.29121/ijetmr.v6.i5.2019.379Keywords:
Fe50Ni50, Ferromagnetic Alloy, Magnetic Properties, Plastic Deformation, Activation Energy, Order of ReactionAbstract
Through the magnetic measurements, isochronal annealing experiments in the temperature 25950 ºC of deformed, quenched, pre-annealed and pulsed laser damage samples Fe50Ni50 alloy revealed the existence of three annealing stages I, II and III in the annealing spectrum of heavily cold-worked by observing the associated changes in maximum magnetic permeability (µmax) on the magnetic field(H) for different annealing temperature. The first annealing stage I appeared in the temperature range from125-500 ºC and it was activated by energy 1.05 eV. It was attributed to the short range order caused by the long range migration of vacancies. The second annealing stage II appeared in the temperature range from 550-750 ºC and it was activated by 1.82 eV, it is associated with an increase in µmax due to the dissociation of vacancy clusters formed during stage I. The third annealing stage III appeared in the temperature range from 750-825 ºC and it was activated by 3.04 eV, it was related to the climb motion of dislocation during the recrystallization process.
Downloads
References
Dudarev, S. L. and Derlet P. M., Journal of Nuclear Materials, 251, 2007, 367. DOI: https://doi.org/10.1016/j.jnucmat.2007.03.009
Derlet, P. M. and Dudarev, S. L., Prog. Mater. Sci. 52, 2007, 299. DOI: https://doi.org/10.1016/j.pmatsci.2006.10.011
Jacques Dalla Torre, Chu-Chum Fu, Francois Williame, Alian Barbu and Jean-Louis Bocquet, J. Nuclear Materials 352,42 (2006). DOI: https://doi.org/10.1016/j.jnucmat.2006.02.040
Chu-Chum Fu, Jacques Dalla Torre, Francois Willaiame, Jean-Louis Bocquet and Alian Barbu, Nature Materials, 4, 2005, 68. DOI: https://doi.org/10.1038/nmat1286
Vicente Alvarez M. A., Marchina M. and Perez T., Metallurgical and Materials Transactions A, 39, 2008, 3283.
Li H. M., Sun D. Q., Cai X. L. and Wang W. Q., Materials and Design, 39, 2012, 285. DOI: https://doi.org/10.1016/j.matdes.2012.02.031
Baicheng Zhang, Nour-Eddine Fenineche, Lin Zhu, Hanlin Liao, Christian Coddet, Journal of Magnetic Materials, 324, 2012, 495. DOI: https://doi.org/10.1016/j.jmmm.2011.08.030
Ebrahimzadeh, H. and Mousavi, S. A., Materials and Design, 38, 2012, 115. DOI: https://doi.org/10.1016/j.matdes.2012.01.037
Gupta, K., Raina, K. K. and Sinha, S. K., Journal of Alloys and Compounds, 429, 2007, 357. DOI: https://doi.org/10.1016/j.jallcom.2006.11.048
Dimitrov, C., Huguenin, D., Moser, P. and Dimitrov, O., J. Nucl. Mater. 147, 1990, 22. DOI: https://doi.org/10.1016/0022-3115(90)90417-L
Ghazi-Wakili, K., Tipping, Ph., Zimmermann, U. and Waeber, W. B., Z. Phys. B: Condensed Matter, 79, 1990, 39. DOI: https://doi.org/10.1007/BF01387823
Anand, M. S. and Pande, B. M., Phys. Stat. Sol. (a), 144, 1994, 285. DOI: https://doi.org/10.1002/pssa.2211440206
Lima, E., Jr. and Drago, V., Journal of Magnetism and Magnetic Materials, 280, 2004, 251. DOI: https://doi.org/10.1016/j.jmmm.2004.03.020
Coutu, L., Chaput, L. and Waekerle, T., Journal of Magnetism and Magnetic Materials 215-216, 2000, 237. DOI: https://doi.org/10.1016/S0304-8853(00)00125-6
Wurschum, R., Kummeler, E. A., Badura-Gergen, K. and Schaefer, H. E., Appl. Phys. 80, 1996, 724. DOI: https://doi.org/10.1063/1.362880
Sumiayma, K., Phys. Stat. Sol. (a), 126, 1991, 291. DOI: https://doi.org/10.1002/pssa.2211260202
Brossmann, U., Wurschum, R., Badura-Gergen, K. and Schaefer, H. E., Phys. Rev. B 49, 1994, 6457. DOI: https://doi.org/10.1103/PhysRevB.49.6457
Schaefer, H. E., Wurschum, R. and Bub, J., Mater. Sci. Forum. 105, 1992, 110. DOI: https://doi.org/10.4028/www.scientific.net/MSF.105-110.439
Schaefer, H. E., Damson, B., Weller, M., Arzt, E. and George, E. P., Phys. Stat. Sol.(a) 160, 1997, 531. DOI: https://doi.org/10.1002/1521-396X(199704)160:2<531::AID-PSSA531>3.0.CO;2-7
Chang, Y. A., Pike, L. M., Liu, C. T., Bilbrey, A. R. and Stone, D. S., J. Intermetal.1, 1993, 107. DOI: https://doi.org/10.1016/0966-9795(93)90028-T
Ali, A. R., Farid, Z. M. and Ghobrial, F. Z., Z. Phys. B 94, 1994, 227. DOI: https://doi.org/10.1007/BF01320673
Gorkunov, E. S., Zadvorkin, S. M., Smirnov, S. V., Yu Mitropol’skaya, S. and Vichuzhanin, D. I., Journal of Physics of Metals and Metallography, 103, 2007, 311. DOI: https://doi.org/10.1134/S0031918X07030131
Hossain Ebrahimzadeh and Seyed Ali Ashghar Akbari Mousavi, Material and Design, 38, 2012, 115. DOI: https://doi.org/10.1016/j.matdes.2012.01.037
Ali, A. R., Ghobrial, F. Z., Takla, E. and Meleka, K. K., Material Science, An Indian Journal, 13, 2015, 108. DOI: https://doi.org/10.4103/2319-5932.159035
Jiles, D. C., Phys. Stat. Sol. (a), 108, 1988, 417. DOI: https://doi.org/10.1002/pssa.2211080144
Dimitrov, O. and Dimitrov, C., J. Nucl. Mater. 105, 1982, 39. DOI: https://doi.org/10.1016/0022-3115(82)90450-0
Mantl, S., Sharma, B. D. and Antesberger, G., Phil. Mag A 39, 1979, 389. DOI: https://doi.org/10.1080/01418617908239279
Anand, M. S. and Pande, B. M., Phys. Stat. Sol. (a), 144, 1994, 285. DOI: https://doi.org/10.1002/pssa.2211440206
Seeger, A. and Kronmuller, M., Mater. Sci. Forum. 15, 1987, 118. DOI: https://doi.org/10.4028/www.scientific.net/MSF.15-18.65
Sharma, B. D., Sonnenberg, K. and Antesberger, G., Phil. Mag. 377, 1978, 777. DOI: https://doi.org/10.1080/01418617808239208
Nakata, K., Takamura, S. and Masasak, I., J. Nucl. Mater. 131, 1985,35. DOI: https://doi.org/10.1016/0022-3115(85)90424-6
Solt, G., Waeber, W. B., Zimmermann, U., Tipping, Ph., Gygax, F. N., Hitti, B., Schenk, A. and Bearren, P. A., "Effect of Radiation on Materials",14th International Symposium, ASTM SPT 1046, Philadelphia, 1990.
Ali, A. R., Farid, Z. M. and Takla, E., Phys. Stat. Sol. (a), 128, 1991, 295. DOI: https://doi.org/10.1002/pssa.2211280204
Ali, A. R., Ghobrial, F. Z., Takla, E., Meleka, K. K., Material Science, An Indian Journal, 14, 2016, 88.
Cullity, B. D., "Introduction to Magnetic Materials", Addison-Wesley Publ.Co., p.357, 1972.
Ali, A. R., Takla, E., Meleka, K. K., Journal of Scientific and Engineering Research, 3, 2016, 140.
Ghazi-Wakili, K., Zimmermann, U., Bruneer, J., Tipping, Ph., Waeber, W. B. and Heinrich, F., Phys. Sol. (a), 102, 1987, 153. DOI: https://doi.org/10.1002/pssa.2211020115
Meechan, C. J. and Brinkmann, J. A., Phys. Rev. 103, 1956, 1193.
Damask, A. C. and Diens, G. J., "Point Defects in Metals", Gordan and Breach, New York, 148, 1963.
Downloads
Published
How to Cite
Issue
Section
License
License and Copyright Agreement
In submitting the manuscript to the journal, the authors certify that:
- They are authorized by their co-authors to enter into these arrangements.
- The work described has not been formally published before, except in the form of an abstract or as part of a published lecture, review, thesis, or overlay journal.
- That it is not under consideration for publication elsewhere.
- That its release has been approved by all the author(s) and by the responsible authorities – tacitly or explicitly – of the institutes where the work has been carried out.
- They secure the right to reproduce any material that has already been published or copyrighted elsewhere.
- They agree to the following license and copyright agreement.
Copyright
Authors who publish with International Journal of Engineering Technologies and Management Research agree to the following terms:
- Authors retain copyright and grant the journal right of first publication with the work simultaneously licensed under a Creative Commons Attribution License (CC BY-SA 4.0) that allows others to share the work with an acknowledgment of the work's authorship and initial publication in this journal.
- Authors can enter into separate, additional contractual arrangements for the non-exclusive distribution of the journal's published version of the work (e.g., post it to an institutional repository or edit it in a book), with an acknowledgment of its initial publication in this journal.
- Authors are permitted and encouraged to post their work online (e.g., in institutional repositories or on their website) before and during the submission process, as it can lead to productive exchanges, as well as earlier and greater citation of published work.
For More info, please visit CopyRight Section