EXPERIMENTAL STUDY OF MEAN DROPLET SIZE FROM PRESSURE SWIRL ATOMIZER

  • Sherry Kwabla Amedorme Department of Mechanical and Automotive Technology Education, University of Education, Winneba, Ghana
Keywords: Pressure-Swirl Nozzle, Sauter Mean Diameter (SMD), Injection Pressure, Axial Distance, Radial Distance

Abstract

This experimental study undertakes the measurements of droplet Sauter Mean Diameter (SMD) at different axial distances for the hollow-cone nozzle and different radial distances from the spray centreline using a laser-diffraction-based drop size analyser in order to validate atomization model. The study also investigates the influence of injection pressure and the evaluation of two exit orifice diameters on the Sauter Mean Diameter (SMD). The drop size distributions along the nozzle centreline as well as the radial drop distributions from spray centreline are also evaluated. To enhance the physics of liquid sheet instability and liquid film breakup mechanisms, visualization of liquid film breakup as a function of injection pressure was carried out. The results show that mean droplet size (SMD) increases in the axial distance on the spray centreline but decreases with an increasing injection pressure on the spray centreline. It was observed that larger sized drops occupy the spray periphery compared to those occupying the spray core. For the nozzle exit orifice diameters of 3.5 mm and 1.5 mm, the results show that the small nozzle exhibits smaller SMDs than the bigger nozzle and the break-up lengths are different for the two nozzles. The drop size distributions at radial positions showed an increase in droplet formation through the spray downstream distances and become more uniform. The visualisation of the spray was carried out using high-speed camera and it was noted that a well-defined hollow-cone spray was captured and that the spray angle increases with the injection pressure but reduces with the liquid film length.

Downloads

Download data is not yet available.

References

Wittig, S., et al., Optical measurements of droplet size distributions: Special considerations in the parameter definition for fuel atomizers. 1984, Karlsruhe Univ (Germany Fr) Inst Fuer Thermische Stroemungsmaschinen.

Broniarz-Press, L., et al., The effect of orifice shape and the injection pressure on enhancement of the atomization process for pressure-swirl atomizers. Crop Protection, 2016. 82: p. 65-74. DOI: https://doi.org/10.1016/j.cropro.2016.01.005

Lefebvre, A.H. and V.G. McDonell, Atomization and sprays. 2017: CRC press. DOI: https://doi.org/10.1201/9781315120911

Malvern-Instruments, Spraytec User Manual MAN0368. 2007, Issue.

Malvern/INSITEC, Method for measuring particle size in the presence of multiple scattering. 1997, Google Patents: US.

Emekwuru, N. and A.P. Watkins, Analysis of a two-fluid sprayer and its use to develop the number size distribution moments spray model, Part I: Experimental Analysis. Atomization and Sprays, 2010. 20(6). DOI: https://doi.org/10.1615/AtomizSpr.v20.i6.10

Lefebvre, A., Atomization and sprays. Vol. 1040. 1989: CRC press. DOI: https://doi.org/10.1201/9781482227857

Emekwuru, N.G. and P. Watkins, Statistical Experimental Analysis of a Two-Fluid Sprayer and Its Use to Develop the Number Size Distribution Moments Model of Sprays. 2007: University of Manchester.

Lefebvre, A. and X. Wang, Mean drop sizes from pressure-swirl nozzles. Journal of propulsion and power, 1987. 3(1): p. 11-18. DOI: https://doi.org/10.2514/3.22946

Chin, J.S., Nickolaus, D., and Lefebvre, A.H, Influence of Downstream Distance on the Spray Characteristics of Pressure-Swirl Atomizers. Journal of Engineering for Gas Turbines and Power, 1986. 108(1): p. 224-224. DOI: https://doi.org/10.1115/1.3239877

Dodge, L.G., Change of calibration of diffraction-based particle sizers in dense sprays. Optical Engineering, 1984. 23(5): p. 626-630. DOI: https://doi.org/10.1117/12.7973346

Hirleman, E.D., V. Oechsle, and N. Chigier, Response characteristics of laser diffraction particle size analyzers: optical sample volume extent and lens effects. Optical Engineering, 1984. 23(5): p. 235610-235610-. DOI: https://doi.org/10.1117/12.7973344

Dombrowski, N. and D. Hasson, The flow characteristics of swirl (centrifugal) spray pressure nozzles with low viscosity liquids. AIChE Journal, 1969. 15(4): p. 604-611. DOI: https://doi.org/10.1002/aic.690150424

PNR UK, L., General Purpose Spray Nozzles, CTG UG20 BR. 6 July 2017.

Crowley, J.M., G.S. Wright, and J.C. Chato, Selecting a working fluid to increase the efficiency and flow rate of an EHD pump. IEEE Transactions on Industry Applications, 1990. 26(1): p. 42-49. DOI: https://doi.org/10.1109/28.52672

Emekwuru, N. and A.P. Watkins, Analysis of a two-fluid sprayer and its use to develop the number size distribution moments spray model, Part II: Computational Analysis. Atomization and Sprays, 2010. 20(8). DOI: https://doi.org/10.1615/AtomizSpr.v20.i8.10

Chin, J. and A. Lefebvre, The role of the heat-up period in fuel drop evaporation. International Journal of Turbo and Jet Engines, 1985. 2(4): p. 315-326. DOI: https://doi.org/10.1515/TJJ.1985.2.4.315

Williams, L.R., Effect of pipe diameter on horizontal annular two-phase flow. 1990, University of Illinois at Urbana-Champaign.

Levy, N., et al., Non-reactive diesel spray computations supported by PDA measurements. 1997, SAE Technical Paper. DOI: https://doi.org/10.4271/970049

Schürmann, P., Forsyth, J., Padrutt, R., and Heiniger, K. C., Spray characterization downstream of swirl pressure nozzle in gas turbine fogging and high fogging applications, in Power-Gen International, Power-Gen International Conf. and Exhibition. 2003, PennWell Corporation:Tulsa: Las Vegas, USA.

Published
2020-12-18
How to Cite
Amedorme, S. (2020). EXPERIMENTAL STUDY OF MEAN DROPLET SIZE FROM PRESSURE SWIRL ATOMIZER. International Journal of Engineering Science Technologies, 4(6), 49-59. https://doi.org/10.29121/ijoest.v4.i6.2020.124