MODELING AND SIMULATION OF SOLAR MODULE PHOTOVOLTAIC WAAREE WSM 330 USED BY THE CENTRAL SOLAR 7MW OF MALBAZA (NIGER)

In order to study the behavior of the solar photovoltaic 7MW Malbaza depending on the irradiation and temperature, modeling of the various components of the system is essential. It is in this context that we have done modeling of a PV module comprising the solar field of the said plant. In this article, we initially presented the basic mathematical model of the photovoltaic cell, reported the equations models with two diodes and a diode, and later considered the case of the model with a diode to perform modeling PV of the central module. Secondly, we implemented the model developed in MATLAB Simulink to study the current-voltage characteristics for different irradiations considering the constant temperature and then for different temperature keeping constant light. The results are similar to the current-voltage characteristics provided by the manufacturer. This allowed us to conclude that the model developed is reliable. Finally, we will study the influence of radiation and temperature on the production of the module.


INTRODUCTION
In a context of energy shortage, Nigerien authorities have focused on improving the production and distribution of electric energy.The use of renewable energy is a viable alternative to meet the energy needs of the population.It is in this context that the construction project of a 7 MW solar photovoltaic power plant connected to Modeling and Simulation of Solar Module Photovoltaic Waaree WSM 330 Used by the Central Solar 7MW of Malbaza (Niger) International Journal of Research -GRANTHAALAYAH 75 the grid in Malbaza (Tahoua Region in Niger).The plant consists of a twenty two thousand one hundred seventy-three (21 273) type modules Waaree WSM 330.In order to perform an optimization of production, we will establish a modeling of this plant to study the influence of parameters weather on production.The model will be simulated on Matlab Simulink.We will initially make a literature review on models of PV cell, in a second time exposing the materials and methods used to develop the solar module and then present the results of the simulation on Matlab.

MATHEMATICAL MODEL OF THE PHOTOVOLTAIC CELL
A photovoltaic cell is described by its current-voltage characteristics (I = f (V)).This modeling is typically used to approximate the output of the cell (voltage, current) as a function of two inputs which are the temperature and the illumination received.Many mathematical models have been developed to represent the behavior of the photovoltaic cells; these models are generally nonlinear resulting from that of the semiconductor junctions which form the basis of their achievements.They derive said reference model or model n diodes Ayachi & Hamdoud (2012).

THE REFERENCE MODEL
The principle of the photovoltaic effect is identical to the operating principle of a diode, and is illuminated when the PN junction is observed the occurrence of a reverse current I at a forward voltage V.A photovoltaic cell in darkness behaves like a conventional diode and it obeys the law Shockley is as follows Ayachi & Hamdoud (2012).
(1) With q: charge of the electron K: Boltzmann constant T: Temperature N: The ideality factor (N = 2 for a silicon diode).In the presence of illumination, this characteristic is modified so as to provide a maximum current which is equal to the short-circuit current (Isc) and maximum voltage which is equal to the open circuit voltage (Voc).The nonlinear part involves several phenomena that will divert part of the current picture generated.These phenomena may be represented by one or more diodes in parallel and optionally a resistor.This allows to achieve a reference model for the photovoltaic cell is: The first diode corresponds to a recombination "band to band"(Shockley model).It reflects the properties of the semiconductor of the cell and is characterized by a short circuit in forward bias.In the case of a small injection (cell concentrations without light), this recombination is limited by the minority carriers and the ideality factor of the diode is N1 = 1.In the case of a large injection (cells with high light concentration), this recombination is limited by the two types of carriers and N1 = 2 Petrone et al. (2017), Wasilla (n.d.).
The second diode corresponds to a recombination of two carriers in the depletion region due to the presence of defects (creating intermediate energy levels).Elleis characterized by an open circuit in forward bias.The diode N2 = 2 ideality factor if the faults are evenly distributed and matches an energy level located in the middle of the band gap (model-Noyce-Sah Shockley).If we deviate from these assumptions, we 1≤N2≤4.
In the case of large injection (cells with high light concentration), there also appears the Auger recombination: a majority carrier is combined with a minority by transferring the energy released at another majority carrier.This phenomenon gives rise to a third diode ideality N3 = 2 / 3.etc.
But generally the most used models are the two diodes and the model for a diode.

THE TWO DIODES MODEL
Indeed, the two diodes model takes into account the power transmission mechanism of the charges within the cell Petrone et al. (2017).
The cell a PN junction photovoltaic subjected to illumination, connected to a load can be schematized by a current generator Iph (the intensity of which depends on the solar irradiance) in parallel with two diodes and a resistance Rsh parallel delivering a current through a series resistance Rs as shown in Figure 2. In this model, the two diodes representing polarization phenomena of the PN junction.The diode d1 represents a short-circuit forward biased and diode D2 is open circuit in reverse bias).
Resistance Rs characterizes the resistivity of the material, that the electrodes and the semiconductor / metal contact.It represents the resistive losses and should ideally be as low as possible to limit its influence on the course of the cell.This can be achieved by optimizing the semiconductor / metal contact, and reducing the resistivity of the material used.
Resistance rsh: parallel resistance, called 'Shunt', comes from the recombination losses due mainly to the thickness, surface effects, as well as non-ideality of the junction.She translated in turn, the presence of a leakage current between the upper grid and the back contact.This value will be as high as possible Petrone et al. (2017), Wasilla (n.d.).

With
• n1 and n2 the respective ideality factors of diodes D1 and D2.
• V: the voltage across the PV cell.

MODEL WITH A DIODE
The model with a diode is obtained by neglecting the recombination of carriers in the depletion zone (IS2 = 0) Petrone et al. (2017).This leads to a "standard" model to a diode.This model, also called four-parameter model was proposed by Townsend and Beckmann.It will therefore have a dependent current source of illumination and a diode in parallel and a series resistance Rs and parallel (shunt) Rsh to consider dissipative phenomena at the cellular level.• Isc: short-circuit current • a: coefficient of photocurrent temperature (or short circuit current), it is often given by the manufacturer, it is generally positive but very weak.• K = 1.38 × 10-23 J / K is the Boltzmann constant; • q = 1.602 × 10-19 C the elementary charge of an electron; • T: the nominal temperature of the cell in Kelvin.
• N: the ideality factor By replacing the current Iph, Id and IRP by their expressions in equation ( 8), the characteristic I (V) is described as follows by: ( 14) Several comparative studies have shown that the model gives a diode peak power values that the two diodes model.So, for the rest of our work, we will consider the model to a diode of the PV cell.

MATERIALS
As material we used the software Matlab Simulink and characteristics of modules provided by the manufacturers.Indeed, 7 MWc solar photovoltaic Malbaza consists of solar modules Waaree type WSM 330 whose characteristics are the following (standard conditions):

METHODS
We used the model to a diode of the photovoltaic cell to develop a mathematical model of the solar module WSM 330 Malbaza.This model is then implanted on Matlab simulation using the features the manufacturer.

MATHEMATICAL MODEL OF A SOLAR MODULE SOLAR POWER MALBAZA
Because of its small thickness, a photovoltaic cell produces a very low electrical power of the order of 1 to 3W.Thus, to increase the power, are assembled these cells either in series or in parallel to form a photovoltaic module and achieve the desired power.A series combination of cells used to add tension, while the interconnection of cells in parallel makes it possible to add the output current of the generator.
The wiring diagram of the solar module may be represented by the following figure: And Is the saturation current given by equation ( 11): • Ish: The current through the parallel resistance given by: (20) Id and replacing Ish by their values in Equation ( 15) was obtained in the current of the solar module by: (21)

IMPLEMENTATION OF MATLAB SIMULINK MODEL 3.3.1. IMPLANTATION OF THE CURRENT EQUATION PROVIDED BY THE PHOTOVOLTAIC MODULE
The photovoltaic current implementation scheme given by equation ( 15) on Maltab Simulink is represented by the following figure:

IMPLEMENTATION OF THE PHOTON CURRENT EQUATION PH
The layout diagram on Maltab Simulink, the photon current given by Equation ( 9) is represented by the following figure:

CURRENT LOCATION OF THE DIODE
The layout diagram on Maltab Simulink, the diode current given by Equation ( 19) is represented by the following figure:

IMPLANTATION OF THE THERMAL VOLTAGE VT
The layout diagram on Maltab Simulink, thermal voltage given by equation ( 5) is represented by the following figure:

IS IMPLANTATION OF THE SATURATION CURRENT
The layout diagram on Maltab Simulink, the saturation current given by the equation ( 11) is represented by the following figure:

IMPLANTATION OF THE SATURATION CURRENT AT THE REFERENCE TEMPERATURE IS-REF
The layout diagram on Maltab Simulink, the saturation current at the reference temperature given by equation ( 12) is represented by the following figure:

SHUNT CURRENT IMPLANTATION (ISH)
The layout diagram on Maltab Simulink, current shunt given by equation ( 20) is represented by the following figure:

IMPLANTATION SERIES RESISTORS (RS) AND PARALLEL (RP)
Series resistance can be calculated at the point  co : (22) The series resistance influences largely on the slope of the characteristic curve (IV) in the vicinity of Vco.It can therefore be calculated by the following formula Khatib & Wilfried (2016) 2017), Skoplaki et al. (2008).They applied for assessing PV cell parameters in Standard conditions.Their approach was later extended to extract the parameters of the cells for any environment.
The hypothesis is to consider Rh → ∞ to the series resistance.Thereby neglecting the current in the branch Rh simplifying the equation of the current.
A further simplification can be made for when the PV panel is in operating condition in a short circuit, the diode included in the model is reversed biased and current is considerably lower than the current photoinduced Iph.The following approximation is valid for environmental operating condition Petrone et al. (2017):

STUDY OF THE CURRENT-VOLTAGE CHARACTERISTIC DEPENDING ON THE IRRADIATION VARIABLE AND CONSTANT TEMPERATURE
The influence of the illumination on the module at a constant temperature of 25 ° C is shown in Figure 16.The simulation results show that the characteristic of the PV module is directly dependent on the illumination.Indeed, the variations of current versus voltage for different levels of illumination at a temperature kept constant 25 ° C show a significant change, whereas the voltage slightly changes with the illumination.On the other hand by making a comparison with the characteristic curve of the 89 manufacturer, found almost the particular points (SAI, Voc, Im, Vm).Which is that the model is reliable and matches the pattern of a WSM330 module.

STUDY OF THE CURRENT-VOLTAGE CHARACTERISTIC TEMPERATURE VARIABLE AND CONSTANT IRRADIATION (G = 1000W / M2)
The influence of temperature on the module at a constant irradiation (G = 1000W / m2) is represented by Figure 19.The simulation results show that the characteristics of the PV module is directly dependent on the temperature.Indeed, the variations of current versus voltage for different temperature levels maintained constant irradiance 1000 W / m², showed Assarid Issaka Abdoulkarim, Adamou Mamane, Noma Talibi Soumaïla, Madougou Saidou, and Boureima Seibou International Journal of Research -GRANTHAALAYAH 90 a slight change, while the voltage changes slightly with temperature.On the other hand by making a comparison with the characteristic curve of the manufacturer, found almost the particular points (SAI, Voc, Im, Vm).Which is that the model is reliable and matches the pattern of a WSM330 module.

STUDY OF THE INFLUENCE OF IRRADIATION ON THE PHOTOVOLTAIC MODULE OUTPUT
The influence of the irradiation on the output is shown in Figure 21: The simulation results show that more radiation increases more the operating point moves upward.So, the increase of irradiation greatly increases production.

THE INFLUENCE OF TEMPERATURE ON PV PRODUCTION
The influence of the irradiation on the output is shown in Figure 22: The simulation results show that the higher the temperature the more the operating point moves down.So, the increase in temperature induces negative module production

CONCLUSION
We have presented in this work, a model of the PV module to explain its electrical operation depending on climatic factors.The simulation module based on mathematical equations showed that the characteristics are strongly influenced by temperature and irradiation.It is observed that the temperature at a slight effect on the current, but an increase in temperature causes an apparent decrease in the short-circuit voltage.Further comparisons made with the characteristic curves given by the manufacturer with those obtained by simulation shows the curves are similar.This proves the reliability of the model developed and can be considered the model of a PV module solar power Malbaza.We show that to increase radiation induced positively on production while the temperature rise induced negatively on production.

Figure 18
Figure 18 Characteristic Current Voltage at T = 25 ° C and G Variable Given by the Manufacturer